Follow
Essam M. Wahba
Essam M. Wahba
Faculty of Engineering, Alexandria University, Egypt
Verified email at alexu.edu.eg
Title
Cited by
Cited by
Year
Multiplicity of states for two-sided and four-sided lid driven cavity flows
EM Wahba
Computers & Fluids 38 (2), 247-253, 2009
892009
Runge–Kutta time‐stepping schemes with TVD central differencing for the water hammer equations
EM Wahba
International journal for numerical methods in fluids 52 (5), 571-590, 2006
572006
Modelling the attenuation of laminar fluid transients in piping systems
EM Wahba
Applied Mathematical Modelling 32 (12), 2863-2871, 2008
512008
A coupled FE and CFD approach to predict the cutting tool temperature profile in machining
S Pervaiz, I Deiab, EM Wahba, A Rashid, M Nicolescu
Procedia CIRP 17, 750-754, 2014
502014
Steady flow simulations inside a driven cavity up to Reynolds number 35,000
EM Wahba
Computers & fluids 66, 85-97, 2012
502012
Aerodynamic drag reduction for ground vehicles using lateral guide vanes
EM Wahba, H Al-Marzooqi, M Shaath, M Shahin, T El-Dhmashawy
CFD letters 4 (2), 68-79, 2012
422012
Numerical simulations of incompressible aerodynamic flows using viscous/inviscid interaction procedures
M Hafez, A Shatalov, E Wahba
Computer methods in applied mechanics and engineering 195 (23-24), 3110-3127, 2006
422006
Non-Newtonian fluid hammer in elastic circular pipes: Shear-thinning and shear-thickening effects
EM Wahba
Journal of Non-Newtonian Fluid Mechanics 198, 24-30, 2013
392013
Turbulence modeling for two-dimensional water hammer simulations in the low Reynolds number range
EM Wahba
Computers & Fluids 38 (9), 1763-1770, 2009
382009
Iterative solvers and inflow boundary conditions for plane sudden expansion flows
EM Wahba
Applied mathematical modelling 31 (11), 2553-2563, 2007
352007
A novel numerical modeling approach to determine the temperature distribution in the cutting tool using conjugate heat transfer (CHT) analysis
S Pervaiz, I Deiab, E Wahba, A Rashid, CM Nicolescu
The International Journal of Advanced Manufacturing Technology 80, 1039-1047, 2015
312015
On the performance of air-lift pumps: from analytical models to large eddy simulation
EM Wahba, MA Gadalla, D Abueidda, A Dalaq, H Hafiz, K Elawadi, R Issa
Journal of Fluids Engineering 136 (11), 111301, 2014
302014
On the performance of air-lift pumps: from analytical models to large eddy simulation
EM Wahba, MA Gadalla, D Abueidda, A Dalaq, H Hafiz, K Elawadi, R Issa
Journal of Fluids Engineering 136 (11), 111301, 2014
302014
A numerical and experimental study to investigate convective heat transfer and associated cutting temperature distribution in single point turning
S Pervaiz, I Deiab, E Wahba, A Rashid, M Nicolescu
The International Journal of Advanced Manufacturing Technology 94, 897-910, 2018
292018
Simulations of viscous transonic flows over lifting airfoils and wings
M Hafez, E Wahba
Computers & fluids 36 (1), 39-52, 2007
252007
Multiphase flow modeling and optimization for online wash systems of gas turbines
EM Wahba, H Nawar
Applied Mathematical Modelling 37 (14-15), 7549-7560, 2013
232013
Numerical and experimental analysis of turbulent flow and heat transfer of minimum quantity lubrication in a turning process using discrete phase model
W El-Bouri, I Deiab, K Khanafer, E Wahba
International Communications in Heat and Mass Transfer 104, 23-32, 2019
222019
Lattice Boltzmann simulations of the capillary pressure bump phenomenon in heterogeneous porous media
HA Warda, SH Haddara, EM Wahba, M Sedahmed
Journal of Petroleum Science and Engineering 157, 558-569, 2017
212017
On the propagation and attenuation of turbulent fluid transients in circular pipes
EM Wahba
Journal of Fluids Engineering 138 (3), 031106, 2016
212016
Computational Fluid Dynamics (CFD) simulation of liquid column separation in pipe transients
HA Warda, EM Wahba, MS El-Din
Alexandria Engineering Journal 59 (5), 3451-3462, 2020
202020
The system can't perform the operation now. Try again later.
Articles 1–20